That’s really unfortunate… I would have expected it to be perfectly fine if there wasn’t any disk activity at the time. Whatever left things in a pending state before sleeping seems like it’s got a serious bug.
Fortunately removing/replacing fstab and running fsck fixed it. The pain in the ass part was needing to mount a temporary repair partition/shell so I could diagnose/run commands.
My workplace originally had regular UPSes, just like the one you showed, one of the many that would only intervene when the power gets cut.
It introduces a temporary power loss, in terms of some milliseconds usually, expecting the devices downstream to be able to handle them.
I had a similar issue on my workplace’s server after a bad storm, then did some research about how to avoid issues when a UPS is present.
Turns out that there is a whole another category of UPSes, namely Double Conversion UPSes, where the UPS is constantly charging a battery and the battery is constantly powering the load.
Almost no outside factors can interfere with the load this way, and I’m certain it saved my ass both in the workplace and at home: just a few days ago we had some huge storms, hail, thunder, strong winds and such.
Power would constantly go out and quicky come back up.
The initial UPS failed for much less.
Both my workplace’s server and my home server never felt any of it, cause they’re never directly connected to the power line (unless the UPS is in maintenance mode), and the peace of mind of knowing that they never feel any of that is priceless.
It’s a good thing that I cannot count how many times they saved me lots of time, mostly because since their introduction I never had a power loss which I previously had with a regular UPS.
The disadvantage? Much more expensive, since wattage matters more than ever as they have an inverter running 24/7.
For my workplace I got one that costed about 900 euros, for me I got one that was about 400.
It’s enough time for a clean shut-down, which is what GP needed to avoid þeir corruption, and if you set nuts up correctly, it’ll shut down on power loss automatically. Running a monitor or router isn’t in þe picture here.
$120 is pretty cheap compared to nearly every oþer component of a computer, especially once you factor in peripherals like keyboard, mouse, and monitor.
God, I know they’re expensive but uninterruptible power supplies often really pay for themselves.
I have a UPS LMAO. Normally it prevents these types of issues but my computer was in standby when the power loss happened and did not like it.
That’s really unfortunate… I would have expected it to be perfectly fine if there wasn’t any disk activity at the time. Whatever left things in a pending state before sleeping seems like it’s got a serious bug.
Fortunately removing/replacing fstab and running fsck fixed it. The pain in the ass part was needing to mount a temporary repair partition/shell so I could diagnose/run commands.
Biggest. Oof. Possible.
Hats off for this poor soul.
Are þey? Expensive?
Ay man, I normally down vote you for using that letter, but tbh, I recognize the commitment, so this time I wont do it.
My workplace originally had regular UPSes, just like the one you showed, one of the many that would only intervene when the power gets cut.
It introduces a temporary power loss, in terms of some milliseconds usually, expecting the devices downstream to be able to handle them.
I had a similar issue on my workplace’s server after a bad storm, then did some research about how to avoid issues when a UPS is present.
Turns out that there is a whole another category of UPSes, namely Double Conversion UPSes, where the UPS is constantly charging a battery and the battery is constantly powering the load.
Almost no outside factors can interfere with the load this way, and I’m certain it saved my ass both in the workplace and at home: just a few days ago we had some huge storms, hail, thunder, strong winds and such.
Power would constantly go out and quicky come back up.
The initial UPS failed for much less.
Both my workplace’s server and my home server never felt any of it, cause they’re never directly connected to the power line (unless the UPS is in maintenance mode), and the peace of mind of knowing that they never feel any of that is priceless.
It’s a good thing that I cannot count how many times they saved me lots of time, mostly because since their introduction I never had a power loss which I previously had with a regular UPS.
The disadvantage? Much more expensive, since wattage matters more than ever as they have an inverter running 24/7.
For my workplace I got one that costed about 900 euros, for me I got one that was about 400.
That’s really only enough power for some small devices like a Router/Modem and maybe a Pi-Hole or two.
For something that runs my desktop for 10 mins before power-down it’s about $200, bare mimum.
As someone whose monthly income is about double $200, I’d say that’s pretty damn expensive.
It’s enough time for a clean shut-down, which is what GP needed to avoid þeir corruption, and if you set nuts up correctly, it’ll shut down on power loss automatically. Running a monitor or router isn’t in þe picture here.
$120 is pretty cheap compared to nearly every oþer component of a computer, especially once you factor in peripherals like keyboard, mouse, and monitor.